|
Product Details:
|
| Product Name: | Wifi Signal Booster | Output Power: | 5W |
|---|---|---|---|
| Frequency: | 5.725G-5.85G | Working Voltage: | 6-18V |
| Size: | 103.5*96.55*30.5mm | Weight: | 0.4kg |
| High Light: | mobile phone signal repeater,cell signal repeater |
||
5W 5.8G WiFi Mobile Signal Repeater Wlan Signal Long Range Project Special Use
Decriptions:
A WiFi extender, sometimes called a wireless network extender or wired-wireless network extender, works a little differently. This type of device uses both wired and wireless technologies to bring a wireless signal to an area of the home where network coverage has been weak (or non-existent).
Advantage:
1. Low noise 3.2dB
The noise figure is an important indicator of the receiver's receiving performance. The current noise on the market is 4.5dB, which can reach 4.0dB, and our industrial grade amplifier can achieve 3.2dB noise. In addition to using high-quality chips from foreign NEC companies, the company also employs industry-leading RF engineers to design, debug and produce. Strictly control every step of the product and every process, so that you get 100% quality products.
2. Voltage 6-18v
This product's power input voltage can reach up to 18V, try to meet the simple requirements of current engineering customers' network layout. It can use POE power supply and POC power supply, which greatly simplifies your wiring complexity, reduces your wiring time, and saves your network cost and Improve your network efficiency, it is the best choice for your engineering network
3. Output power 5000mw
4. Super fan-shaped heat dissipation design
In view of the high output power of the power amplifier, especially the engineering network has high requirements for long-term full-load operation of high-power products. This power amplifier design uses heat dissipation of the conventional CPU for the heat dissipation, and uses the fan teeth on the large heat dissipation substrate. The heat sink can greatly improve the heat dissipation area, so that the heat generated on the circuit board is emitted in a short time to ensure the stability of the product.
Specifications:
| SA-MR37-5.8G | |
| Repeater | |
| Repeater Model | SA-MR37-5.8G |
| Operating range | 5.725G~5.85G |
| Operation mode | Bi-directional, half-duplex, time division duplex |
| Connector type | To radio SMA female (hole inside); To antenna RP-SMA female (pin inside) |
| Output power | 5000mW (37dBm) |
| Input power | 3 ~ 20dBm |
| Transmit gain | 17dB |
| Receiver gain | 14dB |
| Noise figure | ≤3.2dB typical |
| Frequency response | ±1dB over operating range |
| Power adapter | 6-18V, DC 575mA@29dBm 12V |
| Operating temperature | -40°c to +70°c |
| Operating humidity | Up to 75% relative humidity |
| Material | Cast aluminum |
| LED light | Receive red; emission yellow ;signal transmission orange |
| Booster weight | 400g |
| Booster size | 103.5*96.55*30.5mm |
| Antenna | |
| 5.8GHz 6dBi omni whip antenna for WiFi Router/Booster | |
| Compliant with 802.11b/g/n | |
| Frequency Range | 5700-5800MHz |
| Bandwidth | 100MHz |
| Gain | 6dBi |
| VSWR | ≤1.8 |
| Polarization | Vertical |
| Impedance | 50Ω |
| Max power | 50W |
| Lightning protection | DC ground |
| Connection | RP SMA |
| Product Size | Φ1.35*20.5cm |
| Product Weight | 30g |
| Color | black |
| Cable | |
| Cable Type | RG316 Coaxial cable pigtail |
| Length | 20cm |
| Impedanece | 50Ω |
| Connectors | SMA male to RP-SMA male |
Application
1. Hotspot wireless local area network wireless network bridge distance
2. Features For wireless AP, Wi-Fi wireless router Increase the distance the signal effect Increased signal penetration Quick and easy installation Compatible protocol WLAN 802.11b, 802.11b + WLAN 802.11g, 802.11b + g ISM band
Contact Person: Jena
Tel: +8615818561923
