|
Product Details:
|
| Product Name: | Triple Band Mobile Repeater | Frequency System: | 1800Mhz, 2100Mhz, 2600Mhz |
|---|---|---|---|
| Bandwidth: | Wide Band | Output Power: | 20dBm |
| Size: | 228mm×170mm×65mm | Weight: | 4.5kg |
| Highlight: | cell phone signal boosters,cell phone signal extender |
||
Triple Band Mobile Phone Signal Booster 20dBm 1800Mhz 2100Mhz 2600Mhz Wide Band
Descriptions:
1. Triple Band Signal Booster SA-20-DW4G is designed to enhance and improve the quality of three band DCS 1800MHz / WCDMA 2100MHz / LTE 2600MHz connection. There’re black and white colors for options. This model is enough to provide reliable coverage of signal in the area of up to 800 m². It is recommended to use in offices, apartments, houses etc.
2. The model is equipped with an LCD screen in a nice and symmetrical body, which displays the current level of input signal. The information on the LCD screen, greatly simplifies the process of adjusting the gain of the system. The connectors under the screws allow to build device on a wall or other vertical surface.
Features:
1. Coverage up to 800 m²
2. Manual mode for adjusting the gain by “+” / “-” button
3. Smart mode for adjusting the gain automatically
4. Fluted surface on aluminum shell provides an optimal cooling
5. LCD Screen displays the working status of AGC and ISO, gain and power in time.
Support any cellular devices (voice & data & video)
Specification:
| Frequency Range | Uplink | Downlink | |||
| DCS 1800MHz | 1710 - 1785MHz | 1805 - 1880MHz | |||
| WCDMA 2100MHz | 1920 - 1980MHz | 2110 - 2170MHz | |||
| LTE 2600MHz | 2500 - 2570MHz | 2620 - 2690MHz | |||
| Max. Gain | 65dB | 70dB | |||
| Max. Output Power | 17dBm | 20dBm | |||
| Band width | Wide Band | ||||
| Manual Gain Control | 31dB / 1dB Step | ||||
| Automatic Gain Control | >31dB | ||||
| Ripple in Band | 8dB; | ||||
| Noise Figure | ≤ 6dB | ||||
| VSWR | ≤ 2.0 | ||||
| Intermodulation Products | 9KHz~1GHz | ≤ -36dBm | |||
| 1~12.75GHz | ≤ -30dBm | ||||
| Spurious Emission | 9KHz~1GHz | ≤ -36dBm | |||
| 1~12.75GHz | ≤ -30dBm | ||||
| Time Delay | ≤ 1.5 μs | ||||
| Frequency stability | ≤ 0.01ppm | ||||
| MTBF | > 50000 hours | ||||
| Impedance | 50 ohm | ||||
| Power Supply | AC 90-264V,DC 9V/5A | ||||
| Power LED | Power indicator | ||||
| ISO(Alarm LED) | Red | Self oscillation or Strong input signal | |||
| Green | Normal | ||||
| Mechanical Specification | |||||
| RF Connector | N-Female | ||||
| Switch | Power Switch | ||||
| Cooling | Heatsink Convection cooling | ||||
| Humidity | < 90% | ||||
| Operating Temperature | -20°C ~ +55°C | ||||
| Environment Conditions | IP40 | ||||
| Installation Type | Wall Installation | ||||
| Size | 228mm×170mm×65mm | ||||
| Weight | < 4.5Kg | ||||
Instructions:
| Power LED | Green | Normal |
| Off | DC power problem | |
| Smart LED | Green | Adjusting the gain automatically |
| Off | Manual mode: adjusting the gain by “+” / “-” button | |
|
LCD Display |
LCD display will show the real-time gain, “+” increase gain, “-” decrease gain.
|
|
|
SEL |
1. Quickly Press: select the different systems when you need, (only for Dual band, Tri band, Quad-band or Five band repeater) 2. Press for 2 Seconds: select the smart mode or manual mode |
|
Installation:
The booster is fixed onto the wall through expansion bolts.
A. Drill holes on the targeted place and install expansion bolts.
B. Align the holes with the expansion bolts, place flat washers, spring washers, and nuts in turn, and tighten the nuts to fasten the installing support.
C. Place the booster on and fasten it.
D. Connect cables and power cables to the booster respectively.
E. After installing the booster as described above, power on the booster to check the operation status.
Connection:
A. BTS Port: donor antenna cable is connected with Outdoor Port;
B. MS Port: service whip antenna is connected with Indoor Port;
C. DC IN: connected with Power adaptor.
Contact Person: Ms. Jena
Tel: +86-15818561923
